Skip to main content
Se connecter

invis

  • Le dan
  • Portrait de Le dan Auteur du sujet
  • Hors Ligne
  • Membre junior
  • Membre junior
  • Messages : 35
  • Remerciements: 2

invis

il y a 10 ans 9 mois
#
bonjour tout le monde est ce que quelqun a acheter le kit lamello invis mx si oui donner moi une note sur 10 cote satisfaction merci

Connexion ou Créer un compte pour participer à la conversation.

  • Pete 68
  • Portrait de Pete 68
  • Hors Ligne
  • Membre premium
  • Membre premium
  • Messages : 2128
  • Remerciements: 545

Re: invis

il y a 10 ans 9 mois
#
commentaires trouver avec google



Offline promhandicam
Posts: 204

Re: Lamello Invis Mx Starter Kit
« Reply #5 on: January 30, 2013, 05:07 PM »
I've got one and it is good. A couple of things to think about.

1. positioning of the dowels is critical - no room for error.

2. Some people recommend the Rasto jig for aligning the dowel holes but that is another eye watering £330 so only worth buying if you are going to use it a lot.

3. The dowels are expensive so should only be used (IMHO) if there is no alternative - and in many cases there are.

4. Keep a good note (photos) of where the fixings are so that if you ever need to dismantle it you will be able to find them again.

HTH,

Steve
Logged
Offline Captainwrinkles

Posts: 92

Re: Lamello Invis Mx Starter Kit
« Reply #6 on: January 30, 2013, 09:07 PM »
I've used one recently.

I found that it didn't work as well as the video shows. I was using it to join 2" thick maple handrails. I'm not sure if
the density of the maple affected the magnets or if it was because it was quite an old, very well used kit. But i couldn't
get the 2 pieces to pull together as easily as the video shows.

It really took some moving and twisting to get them to pull together and even more to get them apart again.
I had the rasto jig to drill the holes too. It kept it aligned really well. In fact, the Rasto jig is worth every penny. the joints
lined up absolutely perfectly.

I'd recommend the Lamello Zeta P2 system of you want a knock down cabinet. Those joints are solid. They pull really tight and have minimal visibilty when installed (a very small hole for accessing the cam)

Logged
Offline richard.selwyn
Posts: 631

Re: Lamello Invis Mx Starter Kit
« Reply #7 on: January 31, 2013, 02:45 PM »
I'd also recommend the zeta. It couldn't do a handrail though and the Invis really is invis, but I have only ever used mine once. I found knocking the parts down after a real pain. I know that the ones available now are new and improved over mine though.
Logged
Print
Pages: [1] Go Up
Les utilisateurs suivants ont remercié: Le dan

Connexion ou Créer un compte pour participer à la conversation.

  • MarioG
  • Portrait de MarioG
  • Hors Ligne
  • Membre premium
  • Membre premium
  • Messages : 11924
  • Remerciements: 1803

Re: invis

il y a 10 ans 9 mois
#
Les ancrages sont très dispendieux.... autour de 8-9$ chacun donc 16 pour une table à 4 pattes comme dans un de leur vidéo, ça revient quasiment plus cher que le bois de la table.
ébéniste, fabricant d'escaliers sur mesure, réparateur d'outils et machineries.
Les utilisateurs suivants ont remercié: Le dan

Connexion ou Créer un compte pour participer à la conversation.

  • David
  • Portrait de David
  • Absent
  • Administrateur
  • Administrateur
  • Messages : 2061
  • Remerciements: 357

Re: invis

il y a 10 ans 9 mois
#
Salut,

J'en ai un. C'est un de mes bons achats en terme d'outillage. Je fais attention quand je l'utilise pour ne pas utiliser d'encrages pour rien. On peut facilement en mettre 1/2 de ce qu'on planifie en mettant un goujon standard sans colle ou un biscuit pour éviter les torsions. Ça permet bien des choses et l'effet non-permanent d'un assemblage solide est super intéressant. Je 'ai utilisé dans la fabrication d'un "walk-in" récemment. Ça m'a permis d'assemble sur place en un tour de main.

J'espère que ça t'aide

David
Pour l'amour du bois et le travail bien fait

Connexion ou Créer un compte pour participer à la conversation.

  • Le dan
  • Portrait de Le dan Auteur du sujet
  • Hors Ligne
  • Membre junior
  • Membre junior
  • Messages : 35
  • Remerciements: 2

Re: invis

il y a 10 ans 7 mois
#
merci beaucoup david

Connexion ou Créer un compte pour participer à la conversation.

  • Le dan
  • Portrait de Le dan Auteur du sujet
  • Hors Ligne
  • Membre junior
  • Membre junior
  • Messages : 35
  • Remerciements: 2

Re: invis

il y a 10 ans 7 mois
#
merci mario g

Connexion ou Créer un compte pour participer à la conversation.